Olympia Chimney Flue Liner Replacement Nationwide

Olympia Chimney Flue Liner Replacement: The Long Beach Owner’s Guide

We stock and install Olympia Chimney-compatible flue liner replacements in Long Beach, and a typical stainless steel liner swap runs $1,800 – $3,400 installed, depending on flue height, diameter, and whether the old liner comes out clean or needs to be broken up. Most Long Beach jobs are booked within a few days, not weeks. The usual discovery path is predictable: a homeowner books a sweep, our camera goes up the flue, and the footage shows a seam split or corrosion the naked eye never would have caught from the hearth.

Call (562) 317-7262

That camera footage matters. We won’t recommend a liner replacement on a hand-wave. You’ll see the crack, the rust-through, or the separation on screen before you sign anything. And if your Olympia liner is genuinely fine, Hank Delano will tell you that and send you on your way with a clean flue and an honest report.

Which Olympia Chimney Models This Applies To

Olympia Chimney builds two main liner families we see in Long Beach homes: the Series 6 (6-inch inner diameter) and Series 7 (7-inch inner diameter) stainless flex liners, plus a slightly heavier relining pipe in the Series 8 line for larger masonry flues. The quickest way to identify what you have is to look for the silver UL label wrapped around the liner at the top of the chimney, inside the chase, or on the appliance connector. That tag carries the model number and diameter.

If the label is gone, we measure. Inside diameter is the number that decides the replacement, not the outside. For Olympia Chimney specifically, their flex liners are cut-to-length on site from a coil, so the replacement part is not a single pre-boxed unit – it’s a section of liner sized to your exact flue run, which is why getting the diameter and length right on the first measurement matters. We also match the connector type: Olympia liners mate to their Top-Kit and Rain Cap assemblies, and if your existing cap is still sound, we can often reuse it and replace only the liner body.

OEM vs aftermarket: We install genuine Olympia Chimney liner material when the job calls for it, and we also carry DuraFlex, HeatShield, and Gelco products. The decision is made by what fits your existing appliance connector and cap system, not by whichever box is closest to the truck door. HeatShield is a different category entirely – it’s a cast-in-place cementitious resurfacing system that can sometimes re-line a damaged flue without pulling the old metal. If a customer asks about it, we explain when it’s a legitimate option and when a full metal liner replacement is the only honest answer.

Signs Your Olympia Chimney Flue Liner Replacement Is Failing

• Rust flakes or metallic debris in the firebox. This is the most common signal we see in Long Beach. The liner’s inner wall is shedding material, which means the stainless has been eating itself from the inside, usually where the acid-laden flue gases stack near the connector pipe.
• A “wet” or sour smell from the fireplace after rain. Water is working its way past the liner seam or through a rust-through pinhole. In Long Beach’s marine air, salt and moisture accelerate that corrosion, especially on older multi-story homes closer to the water.
• Visible gaps or separations at the liner seam. You can sometimes spot this with a flashlight from below. A separated seam means exhaust is leaking into the chimney cavity, not traveling up the flue path.
• Your carbon monoxide detector trips more often during fireplace use. We treat this as serious. It usually means flue gas is backdrafting or spilling into the living space because the liner is obstructed, separated, or failed at a joint.
• White or brown staining on the chimney chase or walls near the flue. That staining shows the liner has leaked moisture into the surrounding structure. The liner’s job is to keep everything sealed; once staining appears, the liner has failed structurally, not cosmetically.

None of these symptoms are worth waiting on. A failed liner isn’t a performance issue. It’s a containment issue. The liner exists to keep superheated flue gas and carbon monoxide moving up and out of the house. When it fails, you’re not just losing efficiency – you’re losing the barrier that keeps your family safe from what burns in the fireplace. Especially with gas logs, which burn clean enough that the exhaust is harder to see but carries carbon monoxide just the same.

Replacement Cost & What’s Included

A full Olympia Chimney flue liner replacement in Long Beach typically runs $1,800 – $3,400 installed. The spread is driven by flue height (most Long Beach chimneys run 15 – 35 feet), liner diameter (6-inch, 7-inch, or 8-inch), the condition of the existing cap and top plate, and how difficult the old liner is to extract. A straight 20-foot masonry flue with clean access sits at the lower end. A chase-style prefab with tight clearances and a corroded old liner that fights extraction sits at the higher end.

Every Flint Chimney Co Long Beach liner job includes a written price before any work starts, the liner material itself, the top plate and cap if needed, full removal of the old liner, installation of the new one, and a camera inspection after install so you see the finished run with your own eyes. That camera report is part of the job, not an add-on. Every liner replacement carries the 365-Day Done Right Promise: a written guarantee valid for one full year on the repair. If a covered repair fails, we return and correct it at no charge. No argument. That’s The Garrison Standard, the same code every Garrison Partners location follows.

DIY or Call Us?

There are things you can safely check on your own, and things you should not. You can shine a flashlight up the flue from your firebox and look for obvious rust, separation, or debris. You can inspect the cap from the ground with binoculars. You can keep a log of any odors or detector trips. What you shouldn’t do is attempt a liner replacement yourself. The liner runs the full height of your chimney, which means rooftop work, ladder safety, and handling stainless material that’s awkward and heavy even in 15-foot sections. A liner that’s mid-fall or incorrectly seated at the connector is a carbon monoxide risk, not a cosmetic issue.

We do this repair in Long Beach all year, but the marine air means more corrosion near Belmont Heights and Naples than you’d find further inland. We’re independent of Olympia Chimney – we’re not a factory warranty shop – but we’ve installed enough of their liners to know the quirks of their connector system and cap fittings. Call (562) 317-7262 for a straight quote. We’ll tell you what we think based on the measurements and what we find with the camera, and the number we quote is the number you approve.

FAQs