Famco Chimney Repair Nationwide

Famco Chimney Repair in Long Beach: What to Know First

Famco chimney repair in Long Beach usually means one of three jobs: replacing a rusted-out anchor plate, swapping a failed damper assembly, or addressing water damage where the Famco cap meets the flue. We handle all three, and a straight repair typically runs $225 – $675 depending on what’s failed and whether scaffolding is needed. We’re an independent Famco service provider, not a manufacturer-authorized shop, which means we tell you plainly when a part is worth replacing and when the whole assembly should go.

Call (562) 317-7262

If you own a Famco chimney cap, anchor plate, damper, or chase cover in Long Beach and you’re seeing rust streaks, water in the firebox, or a damper that won’t seat, call (562) 317-7262. Hank Delano and the crew at Flint Chimney Co Long Beach will give you a written price before any tool comes off the truck.

How Famco Products Fail – and How We Fix Them

• Famco anchor plates rust through at the bolt slots. The anchor plate is the steel frame that holds the cap to the top of the flue. On older Famco caps, especially the standard single-flue models we see all over Long Beach, the galvanized coating wears thin at the bolt holes first. Salt air off the harbor accelerates it. We replace the plate, not the whole cap, when the cap body is still sound.
• Famco dampers seize at the pivot hinge. Famco’s cast-iron dampers are solid, but the hinge pin collects creosote and moisture over time. In Long Beach’s damp winter mornings, that hinge swells and the damper won’t close or won’t stay open. We remove the damper, clean the hinge seat, and either free it or install a direct replacement. We’ll tell you if the old one is salvageable before we quote a new part.
• Famco chase covers leak at the corners. Famco makes a decent chase cover, but the factory corners are spot-welded, not continuous-welded. After five to eight years near the coast, those corners open up. We fix this one of two ways: continuous-weld the existing cover, or replace it with a thicker-gauge stainless cover cut to the same footprint. We show you the gap before we touch it.
• Famco multi-flue caps collect debris between the screens. We see this on larger Famco caps on older Craftsman chimneys in Belmont Heights. Leaves and pine needles wedge between the mesh screens and the cap body, blocking draft. The fix is a full removal, a thorough screen cleaning, and reseating the cap with fresh stainless hardware. If the screen is torn, we replace it with a matching mesh gauge.
• Famco cap legs loosen where they clamp to the flue tile. The clamp legs on Famco caps work well on round flues but can shift on square or rectangular clay tile. When that happens, the cap sits crooked and water runs into the flue instead of off the cap. We add stainless shims and re-clamp, or bracket the cap to the flue so it can’t walk in the wind. This is a Long Beach problem we fix on repeat, especially on exposed roofs near the water.

Our Famco Chimney Repair Process

1. 1
   We inspect the whole top of the chimney, not just the Famco part. Before we quote a repair, we look at the cap, the flue, the crown, and the flashing. The Famco part is usually one piece of a bigger water puzzle.
2. 2
   We write down what’s actually wrong. You get a described problem and a fixed number. No “we’ll see what we find.” We stand on the roof, we look, and we tell you.
3. 3
   Parts decision, made with you. If a genuine Famco replacement part is available and makes sense, we use it. If the OEM part is obsolete or the design was flawed, we tell you that and quote a quality aftermarket match instead. We don’t charge you a premium for a nameplate.
4. 4
   We do the repair with the right materials. Stainless hardware, proper sealant, and the correct gauge metal. No caulk slathered over rust. If the job needs a DuraFlex liner section or a HeatShield resurfacing instead, we’ll say so before we order anything.
5. 5
   We test what we touched. Damper gets opened and closed a dozen times. Cap gets checked for level and seat. Water path gets re-checked from the crown down. If it doesn’t pass, we redo it before we leave.
6. 6
   You get the guarantee in writing. Every Famco repair carries our 365-Day Done Right Promise. If a covered repair fails within one year, we come back free of charge. No argument, no prorating.

What Famco Chimney Repair Costs in Long Beach

Here are honest ranges for the Famco jobs we do most in Long Beach:

• Anchor plate replacement: $225 – $450
• Damper replacement: $300 – $675
• Cap reseating with new hardware: $180 – $350
• Chase cover repair or replacement: $400 – $900
• Cap replacement (standard single-flue): $350 – $800

What moves the price: roof pitch and access, chimney height (two-story vs one-story), whether the flue is round or square, and whether we’re working on the cap only or also resurfacing the crown underneath. You’ll know the number before we start. Call (562) 317-7262 for a free estimate on your specific Famco repair.

Why Long Beach Homeowners Call Flint Chimney Co Long Beach for Famco Work

We show up inside the window we give you, and we put the price in writing before anything gets unbolted. Every Famco repair, like every repair we do, carries a written one-year guarantee under the 365-Day Done Right Promise: if it fails within that year, we return at no charge. That’s not a marketing line; it’s printed on your invoice.

Our techs know Famco parts and their failure patterns. They also know when a Famco part isn’t the right fix, and they’ll say so even if it costs us the ticket. We stock and work with other professional lines: DuraFlex for liners, HeatShield for flue resurfacing, Gelco for caps and chase covers. So the recommendation you get is the right material for your chimney, not whichever one we happen to carry.

Hank built this crew on the same code he’s worked under since his trade school days at Los Angeles Trade-Technical College, doing chimney work across Southern California. Clean flue, honest report – that’s the whole job. In Long Beach, that includes Belmont Heights Craftsman chimneys, waterfront builds with salt-air rust, and everything in between.

FAQs