Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Long Beach?
Chimney liner and rebuild work in Long Beach typically runs $3,800 to $12,500, with the two jobs often handled together since the liner gets installed after the masonry rebuild is done. A stainless steel flue reline alone usually costs $2,200 to $5,800 depending on liner length and material, while a full chimney rebuild from the roofline up ranges from $4,000 to $9,000 in the Long Beach market. If you call Chimney Liner & Rebuild in Long Beach, we’ll give you a written price before any work begins, so the number you approve is the number you pay.
Chimney Liner & Rebuild Cost Breakdown (2026)
Chimney work is best understood as two separate services that often overlap. The rebuild restores the outer masonry structure, and the liner replaces the inner channel that vents combustion gases. Here’s what Long Beach homeowners can expect to pay in 2026:
| Service | Cost Range (Long Beach, CA) | What’s Included |
|---|---|---|
| Stainless steel flue reline | $2,200 – $5,800 | DuraFlex or Olympia liner, removal of old clay tiles if needed, connection to appliance or fireplace |
| Chimney rebuild above roofline | $4,000 – $9,000 | Demolition of damaged masonry, new brick or block, crown, cap, flashing |
| Partial rebuild (top 2 – 4 feet) | $1,800 – $4,200 | Replacing spalled brick and mortar joints at the most weather-exposed section |
| Combined reline + rebuild | $5,500 – $12,500 | Full masonry repair plus liner installation, often the most cost-effective route when both are needed |
| Chimney crown repair/replacement | $600 – $1,800 | Cracked crown removal and replacement with a proper poured crown |
| Flashing repair or replacement | $400 – $1,500 | New flashing at the roof line, often needed during rebuild work |
These numbers reflect the Long Beach market in 2026, including the cost of permits where required, masonry labor rates in Los Angeles County, and the materials we actually use on site. The spread between low and high comes down to chimney height, access difficulty, and the condition of what’s underneath once we start tearing into the structure.
What Affects Chimney Liner & Rebuild Pricing in Long Beach
No two Long Beach chimneys are the same, and the price difference usually comes down to a few concrete factors. Here’s what moves the number on your written estimate:
- Chimney height and roof pitch. A single-story bungalow in Belmont Heights with a gentle roof slope is a different job than a three-story home in Naples with a steep pitch. Taller chimneys need more liner, more scaffolding, and more labor hours.
- Access to the chimney. Homes in Bluff Park and Alamitos Heights often sit on hillsides where the chimney is hard to reach from the ground. Tight lot lines in areas like Rose Park South can mean ladder work instead of scaffold work, which changes the labor cost.
- Masonry condition beneath the surface. You can’t always see how far salt air and marine layer moisture have penetrated the mortar until demolition starts. Long Beach’s coastal climate accelerates spalling on brick and stone, and interior courses are often worse than the outer face.
- Liner material and diameter. DuraFlex stainless steel liners run more than budget aluminum, but for wood-burning fireplaces and most gas appliances in Long Beach, stainless is the right call. Chimneys serving multiple appliances need larger diameters, which adds material cost.
- Permit requirements. Some structural rebuilds in Long Beach trigger building permit requirements with the city. Permit fees vary by scope, and they’re included in your written quote so there are no surprises.
- Seismic reinforcement. Los Angeles County has seismic code requirements for freestanding chimneys. If your rebuild needs strapping or reinforcement to meet current code, that work gets priced into the job up front.
We price by the job, not by the hour. Before any work starts, the scope is written down with the materials specified: DuraFlex for liners, HeatShield for resurfacing, Gelco or Olympia for crowns and caps, Famco and Copperfield for caps and flashings. You know the names, you know the cost, and you sign only when it’s all in writing.
Is Chimney Rebuild & Relining Worth the Investment?
For most Long Beach homeowners, the answer is yes, and the math is straightforward. A neglected chimney with cracked mortar and a failed liner is not just a cosmetic problem. It’s a fire hazard, a carbon monoxide risk, and a structure that lets water into your roof assembly every time it rains.
Replacing a liner and rebuilding the top section of the chimney costs a fraction of what a full interior renovation runs after water damage spreads through the attic and upper floor. The return isn’t just financial. It’s the difference between a fireplace you can actually use and one that’s been sealed off for safety.
Here’s what we see in the field across neighborhoods like Bixby Knolls, Los Altos, and the Virginia Country Club area: homeowners who rebuild and reline once, correctly, usually don’t think about the chimney again for 20 to 25 years. Homeowners who patch cheaply end up paying twice because the underlying problem was never addressed.
How to Save on Chimney Liner & Rebuild in Long Beach
Chimney work is not a place to hunt for the lowest bid, but there are practical ways to keep the project cost down without cutting corners that matter.
- Combine the liner and rebuild into one project. If both need doing, doing them together saves on mobilization, scaffolding, and overlap labor. You pay once for setup and teardown instead of twice.
- Address problems before they spread. A cracked crown left alone becomes a full top-section rebuild within two or three rainy seasons. Water is the enemy, and Long Beach gets enough marine moisture to keep that process moving year-round.
- Get the scope in writing before work starts. We deliver a written price on every job before tools come off the truck. That means no moved numbers at the door and no surprise add-ons when the job is halfway done. You budget for the real project, not a guess.
- Choose the right material for the appliance. If your chimney only vents a gas furnace, you don’t need a liner sized for a wood-burning fireplace. We specify the liner based on the appliance and the code requirement, not on what’s more profitable to sell.
- Ask about the guarantee. Every repair we complete in Long Beach carries a 365-Day Done Right Promise in writing. If a covered repair fails within a year, we come back at no charge. That’s a full year of not paying twice for the same problem.
If you want a free estimate, call us at (562) 317-7262. We’ll inspect the chimney, write down the scope, and hand you a number you can hold us to.
Chimney Liner Materials: What We Use and Why
We don’t pick materials by what’s cheapest on the supply truck. We pick them by what holds up in Long Beach’s coastal air, which means salt exposure, marine moisture, and temperature swings between cool evenings and hot inland afternoons.
For flue liners, we use DuraFlex stainless steel. It’s a flexible liner system designed for masonry chimneys, and it carries the UL listing required for most installations. Stainless resists the corrosive effects of combustion gases and holds up far longer than aluminum, which we don’t recommend for wood-burning applications.
When a flue doesn’t need a full liner replacement but has surface cracking or gaps, HeatShield resurfacing can restore the flue without demolition. It’s a ceramic coating system applied inside the existing flue, and for the right application it’s a cost-effective middle path between doing nothing and a full reline.
For crowns, caps, and flashings, we work with Gelco, Olympia Chimney, Famco, and Copperfield products. These are names you can look up yourself and verify against the trade standards. If a material isn’t specified in your written estimate, ask why. We’ll show you the spec sheet.
Long Beach-Specific Chimney Conditions We See Every Week
Every coastal city has its own chimney profile, and Long Beach’s is shaped by three things: salt air, marine layer moisture, and century-old housing stock.
In neighborhoods like Belmont Shore and the Peninsula, chimneys sit close to the water and take constant salt exposure. Salt accelerates mortar decay dramatically compared to inland areas like Lakewood or Cerritos. We regularly see brick faces that look fine from the street but have lost the bond between mortar joints, especially on the ocean-facing side of the chimney.
The marine layer matters too. Long Beach fog doesn’t just wet the surface, it seeps into micro-cracks and then sits there. When the afternoon sun burns it off quickly, the expansion and contraction cycle works the cracks wider. After enough cycles, spalled brick starts falling away and water finds a path inside.
Housing age is the third factor. Much of Long Beach’s residential stock was built between 1920 and 1960, and those original clay tile liners are now 65 to 105 years old. Clay tile liners crack over time, and once they crack, they no longer contain the combustion gases the way they were designed to. That’s why so many Long Beach homes scheduled for a “simple rebuild” end up needing a reline too. The structure and the liner age together.
Chimney Rebuild vs. Chimney Repair: What’s the Difference on the Invoice?
We define these three ways on every written estimate so you know exactly what you’re approving:
Repair covers spot fixes: one cracked brick, a small mortar patch, a damaged cap replacement, a flashing touch-up. Repairs in Long Beach typically run $300 to $1,500 depending on material and access.
Partial rebuild covers the top section of the chimney above the roofline. We remove the damaged courses, rebuild with new brick or block, install a new crown and cap, and reflash the roof junction. Expect $1,800 to $4,200 for the top 2 to 4 feet.
Full rebuild means demolishing and reconstructing the entire chimney from the firebox or the roofline up. That’s $4,000 to $9,000 depending on height, material, and seismic requirements.
The relining decision is separate but related. If your clay tile liner is cracked, the chimney isn’t safe to use until it’s addressed. We’ll show you photos of the flue during the estimate so you can see what we see. Then you decide, with the numbers in front of you.
What Happens During a Chimney Liner & Rebuild Job in Long Beach
Here’s how a combined project runs when Flint Chimney Co Long Beach handles it:
Step 1: The inspection. We inspect the full chimney: exterior masonry, crown, cap, flashing, flue interior, and firebox. If the flue has heavy creosote from years of wood burning, we note it. Photos are taken for your file.
Step 2: The written estimate. We write down the scope with line items, the material brands, the permit requirements if applicable, and the total price. You get a copy. There is no verbal estimate and no “we’ll see how it goes” pricing.
Step 3: The work itself. For a combined job, we start with the rebuild. The damaged masonry comes down carefully, the new structure goes up to current code, and the crown is poured with a proper drip edge and expansion joint. Then the liner goes in: the old clay tiles are removed or bypassed, and the DuraFlex liner is pulled through and connected to the firebox or appliance.
Step 4: The documentation. When the job is done, we walk you through what was built, what was installed, and what the guarantee covers. The 365-Day Done Right Promise is written on the invoice, not just mentioned in passing.
If anything fails on a covered repair within a year, you call the same number, and we return at no charge. No re-inspection fee. No requoting. We fix what we built.
FAQs – Chimney Liner & Rebuild Cost
How much does a chimney liner replacement cost in Long Beach?
Chimney liner replacement in Long Beach typically runs $2,200 to $5,800 for a stainless steel DuraFlex system installed in a standard single-flue masonry chimney. The cost depends on flue height, liner diameter, and whether the old clay tiles need removal. Call (562) 317-7262 for a written estimate specific to your chimney.
How much does it cost to rebuild a chimney from the roofline up in Long Beach?
A full chimney rebuild from the roofline up in Long Beach runs $4,000 to $9,000 depending on height, material, and access. Partial top-section rebuilds are less, usually $1,800 to $4,200. Every rebuild we quote includes new crown, cap, and flashing with the price in writing before any work starts.
Is it cheaper to repair or replace a chimney liner?
Repair is cheaper only when the liner has minor surface damage that can be addressed with HeatShield resurfacing, which typically runs $1,500 to $3,000 depending on flue length. If the existing liner is collapsed, severely cracked, or the wrong size for the appliance, replacement with a stainless liner is the correct fix, and “repairing” it is just delaying the inevitable.
How long does a chimney liner and rebuild take in Long Beach?
A combined reline and rebuild usually takes 2 to 4 working days depending on chimney height and masonry condition. Liner installation alone often finishes in one day. We schedule a specific window, arrive in uniform, and clean the work area before we leave.
Does homeowners insurance cover chimney rebuild costs in Long Beach?
Insurance coverage depends on the cause of damage. If the rebuild is needed because of a covered event like a fire, storm, or earthquake, your policy may contribute. If the damage is from deferred maintenance or gradual water intrusion, it typically won’t be covered. We recommend checking your policy before you schedule, and we’ll provide the documentation your adjuster needs.
Can you do chimney liner and rebuild work the same week I call?
In most cases we can inspect within a few days and schedule the work within 1 to 2 weeks, depending on material availability and your neighborhood. If you have an active leak or unsafe condition, tell the person who answers the phone. We keep room in the schedule for urgent chimney issues, and the phone is answered by a live person around the clock.
Get a Written Chimney Liner & Rebuild Estimate in Long Beach
If your chimneys been flagged for a liner issue, a rebuild, or both, the next step is straightforward. Call Flint Chimney Co Long Beach at (562) 317-7262 and we’ll schedule an inspection. You’ll get a written price with the full scope specified: materials, labor, permit costs, and the guarantee. The 365-Day Done Right Promise covers every repair for a full year, and if a covered repair fails, we return at no charge.
We’ve been operating under The Garrison Standard since 2002 as part of the Garrison Partners family of chimney service companies. The code is simple: written pricing before work begins, background-checked technicians in uniform, and a guarantee that’s printed on the invoice. If you’re in Belmont Shore, Bixby Knolls, Naples, Los Altos, or anywhere else in Long Beach, call us. You’ll know the price before the first tool comes off the truck.
Written by Hank Delano, Owner at Flint Chimney Co Long Beach, part of the Garrison Partners family serving Long Beach since 2002.
Pricing reflects the Long Beach market as of 2026. Flint Chimney Co Long Beach offers free estimates – call (562) 317-7262.
What Our Customers Say
"Full inspection with a camera. Found a cracked flue tile and quoted the repair clearly. Did not push."
- Lydia C."Very respectful, wore boot covers, laid drop cloths. Left no soot."
- Jan S."Direct, no nonsense, and polite. Exactly what I wanted."
- Tina W.